|
Dent Machine and Accessories |
|
Z60-28 5” ROLLER This 5” roller gives full support for rolling larger diameter bells for trombone and larger, especially helpful for French horn bells which are thinner and need the support. Helps avoid putting creases in the bell, if you accidentally relax or drop the work area down. This is a 5” “insurance roller” for French Horn.
Z60-28 5” Roller………..$87.50 |
|
Z60-29 TAPERED SLIM ROLLER This tapered slim roller creates a work area inside the small cornet and trumpet sized bells for the same reasons noted in Z60-28.
Z60-29 Tapered Slim Roller……..$87.50 |
|
Z60-30 SMALL CONVEX ROLLER The convex roller was designed for use with all saxophone bell flares, you will see the work patterns develop in 3 different areas.
Z60-30 Convex Roller……………$122.50 |
|
Z60-36 1-1/4” CURVED ROLLER This roller was necessary to properly utilize the Z61-11 tuba arm by allowing you to “go under” the tubing for complete 360 degree coverage of the outside diameter of the tubing being worked on. 1-1/4” curved roller for inside tuba branches.
Z60-36 Curved Roller………………$82.50 |
|
Notes from customers: “I have been thoroughly satisfied with everything I have bought from Ferree’s so far. Thank you!”...Tom. |
|
Z60-37 TROMBONE SLIDE DENT ROLLER These tools work on the same principle as the N87A trombone pliers but were made for repairmen without a lot of hand strength. A little slower to operate than the pliers, they still do the same fine job.
Z60-37 Trombone Slide Dent Roller……$99.50 |
|
DOUBLE RADII ROLLERS Z60-36A SMALL TRUMPET STEM ROLLER This double radii roller was the first step in addressing the cornet and trumpet bell stem tubing. Does both sides” of the bow.
Z60-36A Small Trumpet Stem Roller……$82.50
|
|
Z60-32 30 DEGREE ARM AND Z60-33 7” ROLLER Imagine, if you will, the machine thrown over your shoulder like a set of bagpipes, so that you can better attend to the matters at hand. No more interference of the bell running up against the quill or the arm setting nut. More freedom than you could have ever thought. This ALL NEW combination allows you to go so deep into a bell that you actually can pass the flair and get into the tapered stack to remove kinks and slash dents ( you’ll be tempted to go farther). The new Z60-32 deep finishing, “30 Degree Arm” moves the support arm and business end of the machine back over your shoulder so that is completely OUT OF THE WAY. The new Z60-33, 7” Inch Roller was developed for tubas and provides that extra measure of security that you need when you have an uneven distribution of weight most large brass instruments have. The bigger the horn the bigger the influence of this phenomena. After much testing of the 30 degree arm it was determined it could benefit from a deeper reaching roller that also could extend back to the arm for support. The new Z60-33 will be riding NEXT TO the deep finishing arm and still reach an extra inch into the bell, to pass the point of tangency, so you don’t accidentally crease the bell from inside out, if you relax too much. This arm also works well with the Z60-28 on French Horns, baritones and euphoniums.
Z60-32 30” Arm…………..$67.50
Z60-33 7” Roller………….$87.50 |
|
Z60-36B LARGE TRUMPET STEM ROLLER This double radii roller was a continuum for cornet and trumpet bells and also a “new world” for the trombone work they fit. Does from the tuning slide to the engraving, using the Z60-15 mandrel that comes with the Z60.
Z60-36B Large Trumpet Stem Roller……$82.50 |
|
<Z60-32 30 DEGREE ARM |
|
Z60-33 7” ROLLER > |
|
For Orders & Acct- Ph.: 1-800-253-2261 or 1-269-965-0511 Fax: 1-269-965-7719 You Can Also Email us at : ferreestools@aol.com |
|
Copyright © 2001 Ferree's Tools, Inc. |
|
Z60-35 MEDIUM CONVEX ROLLER The convex roller was designed for use with all saxophone bell flares, you will see the work patterns develop in 3 different areas.
Z60-30 Convex Roller……………$122.50 |