The New Z61S,
Floor Mount Stand
If you have a Z60 Dent Machine with no base;
The New Z61S will:
1) free up your time,
2) do a better job and
3) make you more money, too!
Here is Cliff using the new Z61S Z61S is meant to
"Stand Ready"
Get your Z60 OUT from under your bench, OFF the shelf or OUT of the
closet and PUT it where it can save you time and
Make YOUR Money.
After all, YOUR TIME is Money!
In our travels we have discovered that many of the 600 or so Z60
Dent Machine "tops" that were purchased with NO Z61 bottom section are
STORED under benches or up on shelves, until needed! And then, when
the need does arise, SOMETIMES, it's just "too much trouble"
or "it takes too long", to get it out or down, install it in the
usually mal-fitting or otherwise occupied bench vise, set it up and do the job.
THIS NEW Z61S FLOOR
STAND CURES ALL OF THAT!
Additionally, Ferree's will alter the height, to fit your
requirements at NO EXTRA COST!
Just call and discuss the proper height for your needs. We have
already built some 4" and 6" lower so that the power is where it was needed
to be. As a "rule of thumb", when you are standing, your elbow should be in
line or slightly above the main working rod. In most cases, a reduction of
4" seems to take care of this, when it is required.
Remember, the Average man is still 5'-8" and the Average woman has now
grown to 5'-4", which is up from 5'-2" over the last 40 years or so. A
female repairman may want one accordingly lower so as to best use her
inherent strength. There is no extra charge for this service. It is
very advantages to be slightly over the top of your dent work, whether
working by hand or machine. This way ALL your strength is about where the work is.
The NEW Z61S takes up only 9" (22.8cm) square of your premium shop
space (only 81 square inches or about 520 square centimeters).
We can guarantee you that: IF THE MACHINE IS ALWAYS SET UP, READY TO
GO; YOU WILL USE IT MORE AND GET BETTER AT IT IN
THE PROCESS! That transposes into more efficiency, less time spent and
more $$$ for you.
You know, making your work better and faster has always been our bread
and butter; making it easier in the process; that's the dessert!
Years ago we used to say the whole dent machine would pay for itself in
just a year through the money it saved you in time and labor. NOW, our
customers are telling us, "No, it takes LESS than 6 months."
Just figure it this way. The Z60/61/61E set up with the new discs and
rollers, costs just about the same as a part time employee costs for just 3
months. But, we've got some Z60's out there that have been working for over 40 YEARS.
Everyone who owns a dent machine, regardless of manufacturer, is
welcomed to visit Ferree's compound for a free personal 3 - 4 hour seminar
of instruction for practical and efficient use. We have other machines on
hand to use as examples. Gary has been doing these free research sessions
for over 2 years. Without exception, repairmen are finding how much MORE
WORK they can do, profitably and professionally.
With the new tooling that has been developed over the last 3 years, the
Z60 dent machine can give you the added production of another person or two!
HOW much is that worth?
Think of being able to go
home, ON TIME. With money!
Think about being able to INSTANTLY attack the damaged instrument,
rather than spending 15 minutes "getting ready" to attack it. Also,
nothing to put away, and it's ready for the NEXT TIME! The Z61S bolts to
the floor and holds your Z60 secure. If there is a space problem, it is a
simple "plug in" to re-install the Z60 in the Z61S and just hang the
Z60 on the wall right behind it.
Now, its 30 seconds not 15 minutes to set up. This is
the accessory that has been missing from your arsenal of tools. It is
another arrow in your quiver of alternatives.
"I wanted to send you these pictures because I LOVE
THAT DENT MACHINE!
I thought you'd get a kick out of seeing me use it. It used to be the only
machine I was
intimidated to use but, ever since we got that stand and it is always
set up, I use it a lot
more and can't wait until the next banged up horn comes in!" Jennifer
Nicoletti, Thomas Music, Rochester, N.Y.
Here, is a before/after of the FIRST massive job Jennifer ever did, on a Conn 14I baritone.
"I am very proud of that horn and am tickled that you are showing it off. I swear - I really
do love that dent machine - and my Dad hears it every time I use it!" Take care, Jen
IF, YOU ARE HAVING ANY SECOND THOUGHTS
about acquiring either this Z61S floor mounted stand (or the NEW Bench mount Z60S
stand),
CALL US NOW! Toll Free @
1(800)253-2261
This great time saver, Z61S is only $239.50
because, we want YOU to have it!
Now, YOU can really enjoy the labor saving benefits of a great tool
that you already own, while being more efficient, more productive and more profitable.
::::Bulletin!!::::
If you decide to buy a complete Z61 or Z61E Base Within 1 year
and 1 month from the date of purchase of this great Z61S Stand, Cliff
will take the Z61S back in on trade for the price you paid for it,
assuming, no damage.
That's, 'kind of like', free for a year. Isn't it?
Ferree's Tools-"the most copied tools in the world"
|
